Re: Dell Hardware Recommendations - Mailing list pgsql-performance

From Scott Marlowe
Subject Re: Dell Hardware Recommendations
Date
Msg-id dcc563d10708091858u4f4a3cf9s902cdc9fcd28032a@mail.gmail.com
Whole thread Raw
In response to Dell Hardware Recommendations  (Joe Uhl <joeuhl@gmail.com>)
Responses Re: Dell Hardware Recommendations
List pgsql-performance
oops, the the wrong list...  now the right one.

On 8/9/07, Decibel! <decibel@decibel.org> wrote:
> You forgot the list. :)
>
> On Thu, Aug 09, 2007 at 05:29:18PM -0500, Scott Marlowe wrote:
> > On 8/9/07, Decibel! <decibel@decibel.org> wrote:
> >
> > > Also, a good RAID controller can spread reads out across both drives in
> > > each mirror on a RAID10. Though, there is an argument for not doing
> > > that... it makes it much less likely that both drives in a mirror will
> > > fail close enough to each other that you'd lose that chunk of data.
> >
> > I'd think that kind of failure mode is pretty uncommon, unless you're
> > in an environment where physical shocks are common.  which is not a
> > typical database environment.  (tell that to the guys writing a db for
> > a modern tank fire control system though :) )
> >
> > > Speaking of failures, keep in mind that a normal RAID5 puts you only 2
> > > drive failures away from data loss,
> >
> > Not only that, but the first drive failure puts you way down the list
> > in terms of performance, where a single failed drive in a large
> > RAID-10 only marginally affects performance.
> >
> > > while with RAID10 you can
> > > potentially lose half the array without losing any data.
> >
> > Yes, but the RIGHT two drives can kill EITHER RAID 5 or RAID10.
> >
> > > If you do RAID5
> > > with multiple parity copies that does change things; I'm not sure which
> > > is better at that point (I suspect it matters how many drives are
> > > involved).
> >
> > That's RAID6.  The primary advantages of RAID6 over RAID10 or RAID5
> > are two fold:
> >
> > 1:  A single drive failure has no negative effect on performance, so
> > the array is still pretty fast, especially for reads, which just suck
> > under RAID 5 with a missing drive.
> > 2:  No two drive failures can cause loss of data.  Admittedly, by the
> > time the second drive fails, you're now running on the equivalent of a
> > degraded RAID5, unless you've configured >2 drives for parity.
> >
> > On very large arrays (100s of drives), RAID6 with 2, 3, or 4 drives
> > for parity makes some sense, since having that many extra drives means
> > the RAID controller (SW or HW) can now have elections to decide which
> > drive might be lying if you get data corruption.
> >
> > Note that you can also look into RAID10 with 3 or more drives per
> > mirror.  I.e. build 3 RAID-1 sets of 3 drives each, then you can lose
> > any two drives and still stay up.  Plus, on a mostly read database,
> > where users might be reading the same drives but in different places,
> > multi-disk RAID-1 makes sense under RAID-10.
> >
> > While I agree with Merlin that for OLTP a faster drive is a must, for
> > OLAP, more drives is often the real key.  The high aggregate bandwidth
> > of a large array of SATA drives is an amazing thing to watch when
> > running a reporting server with otherwise unimpressive specs.
> >
>
> --
> Decibel!, aka Jim C. Nasby, Database Architect  decibel@decibel.org
> Give your computer some brain candy! www.distributed.net Team #1828
>
>

pgsql-performance by date:

Previous
From: "Joe Uhl"
Date:
Subject: Re: Dell Hardware Recommendations
Next
From: Decibel!
Date:
Subject: Re: Dell Hardware Recommendations