RE: Synchronizing slots from primary to standby - Mailing list pgsql-hackers

On Thursday, March 28, 2024 7:32 PM Amit Kapila <amit.kapila16@gmail.com> wrote:
> 
> On Thu, Mar 28, 2024 at 10:08 AM Zhijie Hou (Fujitsu) <houzj.fnst@fujitsu.com>
> wrote:
> >
> > When analyzing one BF error[1], we find an issue of slotsync: Since we
> > don't perform logical decoding for the synced slots when syncing the
> > lsn/xmin of slot, no logical snapshots will be serialized to disk. So,
> > when user starts to use these synced slots after promotion, it needs
> > to re-build the consistent snapshot from the restart_lsn if the
> > WAL(xl_running_xacts) at restart_lsn position indicates that there are
> > running transactions. This however could cause the data that before the
> consistent point to be missed[2].
> >
> > This issue doesn't exist on the primary because the snapshot at
> > restart_lsn should have been serialized to disk
> > (SnapBuildProcessRunningXacts -> SnapBuildSerialize), so even if the
> > logical decoding restarts, it can find consistent snapshot immediately at
> restart_lsn.
> >
> > To fix this, we could use the fast forward logical decoding to advance
> > the synced slot's lsn/xmin when syncing these values instead of
> > directly updating the slot's info. This way, the snapshot will be serialized to
> disk when decoding.
> > If we could not reach to the consistent point at the remote
> > restart_lsn, the slot is marked as temp and will be persisted once it
> > reaches the consistent point. I am still analyzing the fix and will share once
> ready.
> >
> 
> Yes, we can use this but one thing to note is that
> CreateDecodingContext() will expect that the slot's and current database are
> the same. I think the reason for that is we need to check system tables of the
> current database while decoding and sending data to the output_plugin which
> won't be a requirement for the fast_forward case. So, we need to skip that
> check in fast_forward mode.

Agreed.

> 
> Next, I was thinking about the case of the first time updating the restart and
> confirmed_flush LSN while syncing the slots. I think we can keep the current
> logic as it is based on the following analysis.
> 
> For each logical slot, cases possible on the primary:
> 1. The restart_lsn doesn't have a serialized snapshot and hasn't yet reached the
> consistent point.
> 2. The restart_lsn doesn't have a serialized snapshot but has reached a
> consistent point.
> 3. The restart_lsn has a serialized snapshot which means it has reached a
> consistent point as well.
> 
> Considering we keep the logic to reserve initial WAL positions the same as the
> current (Reserve WAL for the currently active local slot using the specified WAL
> location (restart_lsn). If the given WAL location has been removed, reserve
> WAL using the oldest existing WAL segment.), I could think of the below
> scenarios:
> A. For 1, we shouldn't sync the slot as it still wouldn't have been marked
> persistent on the primary.
> B. For 2, we would sync the slot
>    B1. If remote_restart_lsn >= local_resart_lsn, then advance the slot by calling
> pg_logical_replication_slot_advance().
>        B11. If we reach consistent point, then it should be okay because after
> promotion as well we should reach consistent point.
>             B111. But again is it possible that there is some xact that comes
> before consistent_point on primary and the same is after consistent_point on
> standby? This shouldn't matter as we will start decoding transactions after
> confirmed_flush_lsn which would be the same on primary and standby.
>        B22. If we haven't reached consistent_point, then we won't mark the slot
> as persistent, and at the next sync we will do the same till it reaches
> consistent_point. At that time, the situation will be similar to B11.
>    B2. If remote_restart_lsn < local_restart_lsn, then we will wait for the next
> sync cycle and keep the slot as temporary. Once in the next or some
> consecutive sync cycle, we reach the condition remote_restart_lsn >=
> local_restart_lsn, we will proceed to advance the slot and we should have the
> same behavior as B1.
> C. For 3, we would sync the slot, but the behavior should be the same as B.
> 
> Thoughts?

Looks reasonable to me.

Here is the patch based on above lines.
I am also testing and verifying the patch locally.

Best Regards,
Hou zj