Re: pgAdmin 4 | Changing Mail From information! - Mailing list pgadmin-support

Then MAIL_USERNAME & MAIL_DEFAULT_SENDER should be same, MAIL_USERNAME = os.environ['MAIL_USERNAME'] MAIL_DEFAULT_SENDER = os.environ['MAIL_USERNAME'] On Tue, Nov 28, 2017 at 7:36 AM, Đỗ Ngọc Trí Cường wrote: > Dear Murtuza, > > Yes, our email server for some security reason had checked and rejected > when the user (used to authenticated) and the "Email From" in Header > Section. > > The authenticated user can not change, and now I'm trying to change the > "Email From" too, but I can't find where I can configure it? > > Please note that, I've already try to put config below into > config_local.py, and config_distro.py also. > > MAIL_DEFAULT_SENDER = 'mail_demo@digi-texx.vn' > > > > > Thank you and best regards, > > > Đỗ Ngọc Trí *Cường* (Mr.) | *Software Development Department* | +84 28 > 3715 5325 > > ------------------------------ > *From: *"Murtuza Zabuawala" > *To: *"Đỗ Ngọc Trí Cường" > *Cc: *"Dave Page" , pgadmin-support@lists. > postgresql.org > *Sent: *Monday, November 27, 2017 10:09:27 PM > *Subject: *Re: pgAdmin 4 | Changing Mail From information! > > Hello, > > I suspect that the mail server is rejecting your email because you're > trying to send from a username which differs from the username you're > logging in as, e.g. you've set the From: to be mail_demo@digi-texx.vn, > which might be not the same as @digi-texx.vn > > -- > Regards, > Murtuza Zabuawala > EnterpriseDB: http://www.enterprisedb.com > The Enterprise PostgreSQL Company > > > On Mon, Nov 27, 2017 at 5:49 PM, Đỗ Ngọc Trí Cường > wrote: > >> Dear Dave, >> >> Thankfully for your feedback. >> I've add this into the config_local.py, and config_distro.py as below: >> >> ############################################################ >> ############## >> # Mail server settings >> ############################################################ >> ############## >> >> # These settings are used when running in web server mode for confirming >> # and resetting passwords etc. >> # See: http://pythonhosted.org/Flask-Mail/ for more info >> MAIL_SERVER = os.environ['MAIL_SERVER'] >> MAIL_PORT = int(os.environ['MAIL_PORT']) >> MAIL_USE_SSL = os.environ['MAIL_USE_SSL'].lower() in ("yes", "true", "1") >> MAIL_USE_TLS = os.environ['MAIL_USE_TLS'].lower() in ("yes", "true", "1") >> MAIL_USERNAME = os.environ['MAIL_USERNAME'] >> MAIL_PASSWORD = os.environ['MAIL_PASSWORD'] >> MAIL_DEBUG = os.environ['MAIL_DEBUG'].lower() in ("yes", "true", "1") >> MAIL_DEFAULT_SENDER = 'mail_demo@digi-texx.vn' >> ############################################################ >> ############## >> >> But unfortunately, it stills not work although I've tried to restart the >> server already. >> >> Could you think is there any config file more? >> >> Thank you and best regards, >> >> >> Đỗ Ngọc Trí *Cường* (Mr.) | *Software Development Department* | +84 28 >> 3715 5325 >> >> ------------------------------ >> *From: *"Dave Page" >> *To: *"Đỗ Ngọc Trí Cường" >> *Cc: *pgadmin-support@lists.postgresql.org >> *Sent: *Monday, November 27, 2017 4:14:19 PM >> *Subject: *Re: pgAdmin 4 | Changing Mail From information! >> >> Hi >> >> On Mon, Nov 27, 2017 at 6:53 AM, Đỗ Ngọc Trí Cường > > wrote: >> >>> Dear all, >>> >>> I'm new from pgAdmin4 (I normally used pgAdmin3 in the past). >>> >>> Now, I'm deploy a server of pgAdmin4 using docker technology ( >>> https://hub.docker.com/r/chorss/docker-pgadmin4/). I've deployed >>> successfully. But noư I face an issue. >>> >>> Our mail-server restricts to send email if the sender does not match >>> with authenticate user (see log below). I've searched in the config and >>> just found out the config about mail server and mail user/password. I can't >>> find the config mail from or mail template. >>> >>> Could you please help me where I can modify it? >>> >>> ************************************************************ >>> ************************************ >>> reply: b'235 2.7.0 Authentication successful\r\n' >>> reply: retcode (235); Msg: b'2.7.0 Authentication successful' >>> send: 'mail FROM: size=1191\r\n' >>> reply: b'250 2.1.0 Ok\r\n' >>> reply: retcode (250); Msg: b'2.1.0 Ok' >>> send: 'rcpt TO:\r\n' >>> reply: b'553 5.7.1 : Sender address rejected: not >>> owned by user mail_demo@digi-texx.vn\r\n' >>> reply: retcode (553); Msg: b'5.7.1 : Sender address >>> rejected: not owned by user mail_demo@digi-texx.vn' >>> send: 'rset\r\n' >>> reply: b'250 2.0.0 Ok\r\n' >>> reply: retcode (250); Msg: b'2.0.0 Ok' >>> send: 'quit\r\n' >>> reply: b'221 2.0.0 Bye\r\n' >>> reply: retcode (221); Msg: b'2.0.0 Bye' >>> ************************************************************ >>> ************************************ >>> >>> Looking forward to your feedback. >>> >> >> You should be able to set MAIL_DEFAULT_SENDER to an appropriate address >> in your environment. There is a full list of available config options at >> http://pythonhosted.org/Flask-Mail/ which should work in addition to >> those shown in config.py. >> >> As a sidenote, you should create config_distro.py (alongside config.py) >> to contain the required settings. Don't edit config.py itself. >> >> -- >> Dave Page >> Blog: http://pgsnake.blogspot.com >> Twitter: @pgsnake >> >> EnterpriseDB UK: http://www.enterprisedb.com >> The Enterprise PostgreSQL Company >> >> >