pg_resetxlog — reset the write-ahead log and other control information of a Postgres Pro database cluster
pg_resetxlog clears the write-ahead log (WAL) and optionally resets some other control information stored in the
pg_control file. This function is sometimes needed if these files have become corrupted. It should be used only as a last resort, when the server will not start due to such corruption.
After running this command, it should be possible to start the server, but bear in mind that the database might contain inconsistent data due to partially-committed transactions. You should immediately dump your data, run
initdb, and reload. After reload, check for inconsistencies and repair as needed.
This utility can only be run by the user who installed the server, because it requires read/write access to the data directory. For safety reasons, you must specify the data directory on the command line.
pg_resetxlog does not use the environment variable
pg_resetxlog complains that it cannot determine valid data for
pg_control, you can force it to proceed anyway by specifying the
-f (force) option. In this case plausible values will be substituted for the missing data. Most of the fields can be expected to match, but manual assistance might be needed for the next OID, next transaction ID and epoch, next multitransaction ID and offset, and WAL starting address fields. These fields can be set using the options discussed below. If you are not able to determine correct values for all these fields,
-f can still be used, but the recovered database must be treated with even more suspicion than usual: an immediate dump and reload is imperative. Do not execute any data-modifying operations in the database before you dump, as any such action is likely to make the corruption worse.
-l options allow the next OID, next transaction ID, next transaction ID's epoch, next and oldest multitransaction ID, next multitransaction offset, oldest and newest transaction IDs for which the commit time can be retrieved, and WAL starting address values to be set manually. These are only needed when
pg_resetxlog is unable to determine appropriate values by reading
pg_control. Safe values can be determined as follows:
A safe value for the next transaction ID (
-x) can be determined by looking for the numerically largest file name in the directory
pg_clogunder the data directory, adding one, and then multiplying by 1048576. Note that the file names are in hexadecimal. It is usually easiest to specify the option value in hexadecimal too. For example, if
0011is the largest entry in
-x 0x1200000will work (five trailing zeroes provide the proper multiplier).
A safe value for the next multitransaction ID (first part of
-m) can be determined by looking for the numerically largest file name in the directory
pg_multixact/offsetsunder the data directory, adding one, and then multiplying by 65536. Conversely, a safe value for the oldest multitransaction ID (second part of
-m) can be determined by looking for the numerically smallest file name in the same directory and multiplying by 65536. As above, the file names are in hexadecimal, so the easiest way to do this is to specify the option value in hexadecimal and append four zeroes.
A safe value for the next multitransaction offset (
-O) can be determined by looking for the numerically largest file name in the directory
pg_multixact/membersunder the data directory, adding one, and then multiplying by 52352. As above, the file names are in hexadecimal. There is no simple recipe such as the ones above of appending zeroes.
A safe value for the oldest transaction ID for which the commit time can be retrieved (first part of
-c) can be determined by looking for the numerically smallest file name in the directory
pg_commit_tsunder the data directory. Conversely, a safe value for the newest transaction ID for which the commit time can be retrieved (second part of
-c) can be determined by looking for the numerically greatest file name in the same directory. As above, the file names are in hexadecimal.
The WAL starting address (
-l) should be larger than any WAL segment file name currently existing in the directory
pg_xlogunder the data directory. These names are also in hexadecimal and have three parts. The first part is the “timeline ID” and should usually be kept the same. For example, if
00000001000000320000004Ais the largest entry in
-l 00000001000000320000004Bor higher.
pg_resetxlogitself looks at the files in
pg_xlogand chooses a default
-lsetting beyond the last existing file name. Therefore, manual adjustment of
-lshould only be needed if you are aware of WAL segment files that are not currently present in
pg_xlog, such as entries in an offline archive; or if the contents of
pg_xloghave been lost entirely.
There is no comparably easy way to determine a next OID that's beyond the largest one in the database, but fortunately it is not critical to get the next-OID setting right.
The transaction ID epoch is not actually stored anywhere in the database except in the field that is set by
pg_resetxlog, so any value will work so far as the database itself is concerned. You might need to adjust this value to ensure that replication systems such as Slony-I and Skytools work correctly — if so, an appropriate value should be obtainable from the state of the downstream replicated database.
-n (no operation) option instructs
pg_resetxlog to print the values reconstructed from
pg_control and values about to be changed, and then exit without modifying anything. This is mainly a debugging tool, but can be useful as a sanity check before allowing
pg_resetxlog to proceed for real.
--version options print the pg_resetxlog version and exit. The options
--help show supported arguments, and exit.
This command must not be used when the server is running.
pg_resetxlog will refuse to start up if it finds a server lock file in the data directory. If the server crashed then a lock file might have been left behind; in that case you can remove the lock file to allow
pg_resetxlog to run. But before you do so, make doubly certain that there is no server process still alive.
pg_resetxlog works only with servers of the same major version.